Monday, 20 October 2014

KARA-Inspired Zippered Mini-Backpack

 photo ready6_zpsab1e19c8.jpg

I've always been more of a shoe than a bag lady, but occasionally the heavens descend in the form of le sac à dos parfait. Sarah Law, the genious behind Kara made one of these moments happen for me. Somehow though, I have a problem with giving money to customs officials that in my opinion should not benefit in any way from my obsession with leather goods. And since I couldn't easily find this specific Kara bag in Toronto, the next step was quite obvious.

TOOLS:
 photo 0Tools_zps725b74ca.jpg  photo 0Tools2_zpsd97f7045.jpg
Leather (depending on the desired size of the backpack, my piece was 85cm x 28cm)  |  Scissors  |  Zipper (again, depending on the size of the bag, mine was 45 cm)  |  Thread & Sewing machine  |  Rivets and the tool that goes with them (I used 6 regular ones for the bag, and four screwable ones for the straps + mini screwdriver)  |  2 leather straps, I used belt strap, 80 cm each  | Hole-puncher  |  Optional: equal amount of interfacing as leather, if the leather needs some firmness

I. Start by drawing out your pieces. You really only need one long strip of leather, mine was 28 cm wide and about 85 cm long. Cut off an about 20 cm piece at the end (this will make the back piece shown in step ). You should be left with an approx. 65 cm long piece. Mark the spot for 1/3 of the piece's width, and cut there.
 photo 1measureandmark_zpse37bcfc1.jpg
II. Once cut, with a cotton cloth in between, iron a small fold on the long edge of the two pieces you just cut. This will help with sewing the zipper. Add interfacing if required.
 photo 3ironedges_zps8215db0e.jpg
III. Mark the spot for the zipper. You don't want it to go all the way, I had it end 10 cm from the edge. Sew a straight stitch along the edge, stopping at the marks.
 photo 4markzipperlength_zps4deae779.jpg  photo 5sewnzipper_zps9f54eb31.jpg
IV. Measure the distance from the end of the zipper to the edge, and cut a piece that size (with 1 cm extra in length, to make a fold as shown below).
 photo 6measureendpiece_zpsd8c6fd34.jpg  photo 7endpiece_zps95345031.jpg
V. Complete the stitch, securing the end piece in place. Repeat for the other end.
 photo 8endpiecesewn_zps543e4b69.jpg
VI. Fold the raw edges to the back like this.
 photo 9fold_zps9eeb6cf6.jpg
VII. From the piece you cut off at the start, cut off a triangle (mine was 12 cm at the base), pressing folds at the edges with an iron and cotton cloth in between like so:
 photo 10backtriangle_zpseac356a4.jpg
VIII. Sew a straight stitch right at the edge of the triangle, securing the back piece in place.
 photo 11sewnback_zps4013757a.jpg
IX. From the piece that you have left, cut out the bottom. The circumference should be the same as what the main bag piece measures at the bottom.. Cut the corners a bit round to help with sewing.
 photo 12cutbottom_zpsf2ed6266.jpg
X. Attach the bottom piece to the body of the bag with paperclips, binder clips, or whatever works. Sew a straight stitch all around.
 photo 13attachbottom_zps2066babb.jpg  photo 14sewnbottom_zps6b3f9952.jpg
XI. Make a small fold at the top edge of the bag, and sew a straight stitch. You only really need this at the front, I left the top edge at the back unfinished to avoid bulging when folding in the next step.
 photo 15sewntopedge_zps843c05f0.jpg
XII. Fold a couple of darts to give the bag some form, and fold the edge over.
 photo 16foldtopedge_zpsc207eb48.jpg  photo 17foldagain_zpsa7653cb3.jpg
XIII. Start punching holes to attach the fold with rivets. Mark the spots through the holes with a pen.
 photo 18makehole_zpsfa78c867.jpg  photo 19markthespot_zpsd722d550.jpg
XIV. Secure the rivet with the tool (if you're unsure, youtube has some good videos on this. Just search for 'setting a rivet').
 photo 20insertrivets_zpsb25c340f.jpg  photo 21securerivet_zps12041b6c.jpg
XV. Add as many rivets as required to secure the fold in place. I did a total of six with the ones at the edges being a bit lower to keep it nicely pinned down.
 photo 22rivetsdone_zps4e56ac2e.jpg
XVI. Now for the straps. Punch holes at the centre ends of both straps.
 photo 23holeinstrap_zpsde8b9cb4.jpg
XVII. Insert the screwable rivets into the holes.
 photo 24insertrivets_zps08904518.jpg
XVIII. Use the rivet to press down onto the leather where you want the strap attached to mark the spot. Punch a hole there and insert the screw end of the rivet. Screw the rivet ends into each other. Repeat for other strap, and do the same thing to attach the other ends of the straps to the bottom of the bag.
 photo 25markthespot_zps10cce26f.jpg  photo 26insertrivet_zpsa153ab2f.jpg  photo 27tighten_zpseafa4b4b.jpg
The screwable rivets at the ends of the straps are good for allowing for movement when the bag is worn on just one/both shoulders, as the strap can spin around on the rivet.
 photo 28ready_zps15758dcb.jpg
 photo ready3_zps7c5796fa.jpg  photo ready8_zps412ebb13.jpg
Madewell knit, Paige jeans, Selfmade bag

xo,

Julia

4 comments:

  1. Nice Diy! Congratulation!
    www.bonnie-bandie.com

    ReplyDelete
  2. Nice Diy! Congratulation!
    www.bonnie-bandie.com

    ReplyDelete
  3. Great website this post gave me all useful information which I wanted to know I liked the collection and the way you described it. Check the trend in Online Dresses Shopping UAE

    ReplyDelete

I would love to hear what you think and learn about your DIY adventures!

 

Contour Affair Copyright © 2011 -- Template created by O Pregador -- Powered by Blogger