Tuesday, 27 January 2015

How To: Lined Longline Windowpane Vest

 photo ready8_zpsc8d3e5fb.jpg
Grid Obsessions, part II. Making a lined anything can be a bit of a mind-bender. A vest is one of the best pieces to start your lining adventures with, as there's minimal risk of ending up with a sewn-shut lump of fabric and having no clue where you went wrong.

In choosing the pieces I make, I usually go with the holy trinity of functionality, minimalism/simplicity, and inspiration. If it's wearable with the majority of my wardrobe, simple enough to remain a favourite regardless of changing fashions, and if I can visualize it or have seen something on a runway I think I can re-create, it's happening. With this particular project, the clarity was pristine - If you ask me, the grid pattern will never be out of style, clean lines go with everything, and my office tends to get freezing in the winter, so this little darling is the perfect layering piece over lighter shirts.

TOOLS:
 photo 0Tools_zps9594d230.jpg
Fabric (Mine is a light wool, 1 m + lining, same amount)  |  Measurement tape  |  Scissors  |  Pins  |  Fabric marker  |  Sewing machine & thread

I. Start by taking some measurements from an existing light coat or blazer (the key spots are the width of your back and how wide you want the front panels of the vest to be). Trace 3 pieces on your fabric, and repeat the process to get identical pieces of lining. Cut out and you should have 6 pieces. Finish the edges with a zigzag (I only did the lining, wool doesn't really fray). I added an extra 7-ish cm to center of each front panel, because I wanted to have the main fabric make the fold instead of the lining starting right at the edge (see step III to get what I mean).
 photo 1Trace_zps5f460aec.jpg  photo 2Cutpieces_zpscbcc43bd.jpg
II. Place the pieces together right sides facing, pin the shoulders, and sew.
 photo 3pinshoulders_zpsa5e291b8.jpg photo 4shouldersewn_zps417a6920.jpg
III. Insert the lining against the vest, wrong sides facing each other. At this point I trimmed the front pieces of the lining to fit as I ironed a the fold in the grid fabric you see below. Then pin the lining to the front edge as shown in the second image. [Note - if you want to go the easier way, just make the front panels the shape you want with a regular seam allowance, and sew normally along the edge as you see I did for the back of the neck and the arm holes in the next steps.]
 photo 5insertlining_zps826c3220.jpg  photo 6pinfrontlining_zps2988912a.jpg
IV. Pin the back of the neck together and sew together with a straight stitch.
 photo 7pinbackofneck_zpsd5499705.jpg
V. Now for the arm holes. Just like you did with the back of the neck, pin the lining to the vest and sew around the hole. At this point I also trimmed the excess off the front panels.
 photo 8pinarmholes_zps74116e75.jpg
VI. The finish line is on the horizon. Turn the vest lining facing out and pin the side seams together, right sides facing, first the vest and then repeat for the lining.
 photo 9pinsideseams_zps32899c4c.jpg
VII. Last, there are two options. You could sew the hem to the lining the same way as the side seams, leaving a 10-15 cm gap at the center of the back. This gap will let you turn the vest right side out, and then you can hand sew the gap shut. I wanted to make sure the lining didn't end up creating any weird pulls that prevent the vest from fitting nicely, so I instead just finished the vest hem and the hem of the lining by ironing them with hemming tape in between the fold.
 photo 10finishhem_zpscbcb4c78.jpg
VIII. Press the entire project and cozy up.
 photo ready3_zpsc1fd1368.jpg  photo ready9_zps18ae3013.jpg  photo ready1_zps075612d0.jpg

xo,

Julia

1 comment:

I would love to hear what you think and learn about your DIY adventures!

 

Contour Affair Copyright © 2011 -- Template created by O Pregador -- Powered by Blogger