Friday, 6 November 2015

Wardrobe Staples: Light Open Front Longline Blazer

 photo ready2_zpsfajz6lwv.jpg
I really don't like to waste anything (reusing zip lock bags anyone?), and it sometimes bites me in the butt when it comes to fabric shopping. I had gotten just enough of this beautiful light grey cotton recently with the plan of making a simple dress/tunic, but later decided it should be a jacket instead. And instead of getting more fabric (which would have involved having the patience to go back to the store and postpone my project) I had to make it NOW. So had to come up with an interfacing hack for the collar - I actually did not have enough fabric for its lining. Overall what I did here is a total cheater's method for a notched collar, I've got another post lined up with the proper way of executing this. If you want to be a proper seamstress don't do anything I would do!


TOOLS:
 photo 0 Tools_zpsjcrrewtd.jpg
Fabric (I used 2 m but to the last square inch, 2,5 m is safer, even more if you want a longer jacket) + I used a small piece of interfacing (about 50 cm x 10 cm) for the collar  |  Scissors  |  Pins  |  Thread & sewing machine  |  Fabric marker


I. Here are my cut pieces for the back and sleeves. The adjustments you might want are the length of the jacket, and the length of the sleeve (my sleeves are almost always rolled up, so I made them a bit cropped at 55 or so cm, to avoid a bulky fold). I'm a EU 36/US 4.
 photo 1 Cut front and sleeves_zpsgmowfrgf.jpg
.. And for the front. You may want to zig-zag/serger raw edges if they fray. You'll need one more piece, the collar, but I cut that one later once I had the neckline sewn, to get the correct measurement.
 photo 1 Cut front pieces_zpsqbr8u3sf.jpg
II. I started with the back, taking the left back piece and folding 1 cm at the center seam, pressing the fold, and securing it with a straight stitch.
 photo 2 Fold center of left back piece_zps8vtan68r.jpg
I then pinned the back piece centers together, right sides facing, and sewed down about 2 cm from the edge.
 photo 3 Pin and sew center back_zpsnnfjnvdq.jpg
Then pressed both seam allowances to the right, and hand-stitched the fold on the upper part of the now created vent to avoid a visible seam on the right side.
 photo 4 Done back slit_zpsppcabhfm.jpg
III. Next the shoulder seams. Pin the two front panels at the shoulder lines to the back piece, right sides facing. I pinned the front sides just slightly higher than the back piece:
 photo 5 Pin shoulders_zpsex63shom.jpg
.. So I could fold the seam allowance over that of the back piece on the reverse, and stitch again on the right side for a flat-felled seam.
 photo 6 Done shoulder seams_zpscjydt8jb.jpg
IV. Then pin the long rectangular lining pieces to the front seams of the two front panels, right sides facing.
 photo 7 Pin front lining_zpssag5yfcr.jpg
.. And sew along the edges, starting a couple cm from the edge so you can fold it in after. Trim excess, especially around the corners.
 photo 8 Sew and trim excess_zpsjzjjnddg.jpg
Fold right side out and press. Also press a small (0,7 cm or so) fold to the free edge of the lining piece.
 photo 9 Pressed front pieces_zpswac419nd.jpg
V. Fold the neckline and press.
 photo 10 Fold and press neckline_zpsnvnpfh3z.jpg VI. Make the collar but measuring the length marked in the image above (Mine ended up being 50 cm long) and cut a piece of that length x about 9 cm. Cut an equal part of interfacing (or if unlike me you have enough fabric for our project, you can make this the proper way and cut two pieces of fabric, attaching the interfacing to one of them).
 photo 11 Cut collar_zpsd5ea0p4y.jpg
After pressing the interfacing onto the collar through a wet cotton cloth, I folded the edges twice (1 cm fold). Note you want to fold the long edge first, then the short edges. At this point, had I had enough material, I would've placed the rectangles together right sides facing and sewed along the edges, to turn right side out and press for a ready collar piece.
 photo 12 Fold and slit stitch edges_zpsunhnlyt3.jpg
I then pinned the collar onto the coat, right side facing reverse side of coat (the collar folds so the side where I attached the interfacing wouldn't be visible on the finished garment).
 photo 13 Pin collar_zpsmakhflte.jpg
Mainly out of laziness I first machine-sewed the back part:
 photo 14 Sew center back part_zpssgrnnepl.jpg
And then slip-stitched by hand the collar onto the coat on both sides. To create the notch I slipped the collar piece under the front panel lining, and added an unnoticeable stitch to secure it all in place.
 photo 15 Slip stitch both sides of collar_zpsq9e1ns89.jpg
VII. To prepare for the last seams, pin the sleeves to the arm holes (right sides facing the right side of the jacket), and sew along the curved edge. Press the seams open.
 photo 16 Pin sleeves_zpsuljhj7uj.jpg
VIII. Then pin the sleeves and the sides. I pinned mine so the front side came just a bit lower, cause I wanted to do flat-felled seams. You could just pin these normally at equal seam allowances on both sides and press the seams open.
 photo 17 Pin sides and sleeve underarm_zpsmyndtlug.jpg
To create my clean finishes on the reverse side, I pressed the longer seam allowance over the shorter one..
 photo 18 Press seam fold_zpsqzqpvwbh.jpg
.. And added a slip stitch by hand all the way.
 photo 19 Slip stitch seams_zps6ltzaira.jpg
The last step is to finish the hem (I did a double fold of about 1 cm and slip stitched that as well) and the sleeve hems (there I just zig-zagged them since I'll always wear them rolled up).

 photo ready1_zpsxt78vipb.jpg  photo ready3_zps76jqjta2.jpg  photo ready4_zpsvotorujr.jpg
xo,

Julia

1 comment:

  1. wow j'adore ce que tu fais. Je suis une débutante dans la couture... j'ai cherché longtemps a faire ce genre de Blazer j'espère pouvoir le réussir comme toi

    ReplyDelete

I would love to hear what you think and learn about your DIY adventures!

 

Contour Affair Copyright © 2011 -- Template created by O Pregador -- Powered by Blogger